Nine years ago, a young hot rod shop built a 1956 Ford F100 for a local customer. Today, that same shop has torn it apart and built it again with a twin turbo Coyote under the hood.

A vintage pickup truck parked on a street.

The shop is Fat Fender Garage in Arizona, and the visitor was the host of Autotopia LA, who spent a day with the truck and its builder, Jason.

The host’s first reaction behind the wheel said it all: “Wow. Okay, this thing cooks. This thing definitely parties.”

“We Were A Three-Year-Old Company And I Had No Idea What I’m Doing”

Jason is blunt about the original job. The shop was only three years old, and he says they were trying to figure out where they fit in an industry that had existed for decades.

The customer later saw where the company had advanced to and told them, in Jason’s words, that they had better products now than what he had been given. So the owner asked for a “take two.”

There was one catch. The truck already had good paint and bodywork, and Jason’s crew had to swap the chassis, engine and interior without damaging it. They promised only a bit of paint touchup, handled by the shop’s SEMA-level paint team.

He Wanted His Old 302 Ripped Out After One Ride

The first time around, the truck had a 302. When the customer asked about the Coyote engines the shop was installing, Jason took him for a ride in someone else’s Coyote truck.

“Sold. Went around the block. He said, ‘Rip my motor out. Put a Coyote motor in it.’”

This time he asked a bigger question: what about twin turbos? Jason says the Coyote takes up most of the room, and mounting turbos proved harder than they thought.

The Turbo Setup That Fought Back During Tuning

The tuner told the shop they were not getting all the boost and performance out of it. Jason’s crew had to redo some of the piping and put different blowoff valves in different places.

It paid off. The stainless piping is neatly welded and well packaged, and the host, a self-described Ford guy, admits the Coyote is “kind of an ugly engine” but loves the performance. The truck has not been dynoed, though Jason estimates it safely makes 750 to 800 horsepower at the crank.

It uses a six-speed 6R80 automatic and a Ford Racing control pack, so the engine and transmission talk to each other. A 9-inch rear end and a Fat Fender air ride chassis sit underneath.

Gray Paint, Bronze Wheels And A Quarter Inch Off The Ground

The color comes from a Porsche GT3 shade from roughly ten years ago. Jason says the truck originally had red wheels and a red chassis, but they would not build it that way today.

The wheels are 20 inches all around, nines up front and twelves in the rear, with carbon barrels and bronze accents from ID Clawson. Wilwood brakes sit at all four corners with custom yellowish calipers.

Jason prefers the truck a quarter or half inch off the ground. That way it looks laid out without risking a rocker on a rock.

A Customer’s 3D Printed Lights Still Look Good

One detail stayed from the first build. The customer bought a 3D printer and made the lights himself nine years ago, and Jason says they do not look dated.

The wood bed is made at the shop’s cabinet and mill shop by Jason himself. He cuts, fits and stains it in house, and he says their bed is “probably the nicest out there.”

The only thing the shop does not do in house is powder coating. Everything else, from paint to fab to interior, happens under one roof.

The Dash Hides The Air Controller, And The Kit Is For Sale

Inside, the kit includes door panels, kick panels, fiberglass headliner and back wall, and Dakota Digital gauges made for a 1956. Jason says anyone with a similar F100 can order it and expect a seamless install.

He is proud of the air management controller. Rather than letting it flop around on the seat, the shop built it into the dash, and there is a spot for a phone too.

The audio runs on Bluetooth with subs in the back.

1,000 Miles Before Anything Is Handed Over

Jason says every vehicle goes through a 1,000 mile test before the customer gets it. The first 100 or so dial it in, and the next 900 prove it out.

This truck had about 300 miles when the host drove it. “We’re not offering a science project,” Jason says, adding that they test their own products so customers do not.

The host liked the result. The truck was manageable, with a smooth transmission and quick steering. He said he is “not the thousand horsepower guy,” and this one was “not too much power that you feel scared, but enough.”

“Get Those Burnouts, Jason”

On the road, the host leaned into the throttle. “Wow. Wow. Wow. I didn’t want to get so much speed.” A turn was coming, and he backed off.

Then came the call: “Get those burnouts, Jason.”

Right when they finished the last shot, the rain poured down. The host called it a “killer first day of shooting.”

Why Jason Says “Just Drive” These Trucks

Both men agree that classics should be driven. Jason sees customers paying to store cars they never use. “Just people just need to drive these things.”

The host says a custom truck done right keeps the charm of the original. He would never drive a bone stock 1956 F100, he adds, and people today want to take long trips in their classics.

Power deserves respect too. The host calls those numbers “a lot,” and Jason backs him up with the story of a customer with a 564 who did a burnout, then another, and ended up upside down in the bayou. It is a reminder that even 750 horsepower can get away from a driver.

More Stories You May Like

Leave a Reply

Your email address will not be published. Required fields are marked *