Sitting inside a 1968 Plymouth Road Runner project is a 383 big block Mopar engine that will not turn over. Not a groan, not a slow crank. It is locked up solid. Builder @mcmillanbuildz decided the engine was worth a shot, and he walked through a series of tricks to try to free it.

Left, a man pouring hot oil into a seized big block Mopar engine; right, a close-up of engine valve train parts.

The plan ends with boiling motor oil, a full jug of rust dissolver poured down the carburetor and a 24 hour soak.

@mcmillanbuildz

The Oil In The Crankcase Looked “Little Dirty But Not Too Shabby”

He started at the bottom by pulling the drain plug to see what was inside the crankcase. To his surprise, the oil was a little dirty but not too shabby, which is a good sign for an engine that has been sitting.

Next he popped off the air cleaner and gave the area around the intake a quick cleaning. The goal was to keep any dirt from falling into the engine while it was open.

Plugs Out, Valve Cover Off And A Rocker Assembly Pitted With Rust

He then removed the spark plugs one at a time. Pulling them frees up compression in each cylinder, which makes the engine much easier to turn by hand.

After that he took off the bolts on the driver side valve cover and gave it a few polite knocks to break the seal. What he found was mixed news. The rocker assembly was pitted with oxidation, but there were no broken rocker arms and no bent pushrods.

“With that peace of mind,” he went ahead and tried turning the engine over with a breaker bar. It did not move.

A Breaker Bar And Then A Pipe Wrench Could Not Budge The Engine

He added a pipe wrench for extra leverage, but she still did not want to go. That was the point where he moved to plan B.

First came a generous amount of penetrating oil, shot down each spark plug hole until it started coming out the top. Then he dumped a couple of jugs of Marvel Mystery Oil down both sides of the rocker assembly to help lubricate the oil system.

An Entire Jug Of Rust Dissolver Goes “Down The Hatch” Through The Carburetor

“Then comes my favorite part,” he says. “Alright, down the hatch.” He poured an entire jug of rust dissolver straight down the carburetor, hoping it would work its way down to free up the lifters and anything else in its path.

Then came the move he had only heard about and never tried. He boiled motor oil, using 0W-20 in hopes it would be thin enough to seep into every nook and cranny of the engine. His one warning to viewers was not to let the pan slip out of your hands.

He admits the process made a huge mess, but says he has high hopes it will work. Both valve covers went back on to seal in the chemical mixture, and the whole concoction was left to soak for about 24 hours.

About The Engine In A 1968 Road Runner

The Road Runner nameplate arrived in 1968 as Plymouth’s no-frills muscle car, and its standard engine was a 383 cubic inch big block. That makes a locked up 383 exactly the kind of engine a Mopar builder would want to save rather than replace, since it can keep the car close to how it left the factory.

The 383 is a member of Chrysler’s B-series big block family, a design known for being tough and fairly simple to rebuild when the bores are in good shape. The oil and parts in this one were in better condition than many that have sat.

How Builders Try To Free A Stuck Engine, Step By Step

The method in this video follows a pattern used by many hobbyists with a seized engine. If you have an old engine that will not turn, these are the steps that came out of it.

  • Check the oil first. Dirty oil is fine, but milky oil or water in the crankcase suggests deeper trouble.
  • Pull every spark plug so the pistons are not pushing against trapped air.
  • Look at the valve train. Broken rocker arms or bent pushrods would point to a mechanical problem, not just rust.
  • Use a breaker bar on the crank bolt and go slowly. Brute force can bend things, so patience matters more than muscle.
  • Let penetrating oil soak in for hours, not minutes. Time does a lot of the work.

His own chemical soak was the plan for the next 24 hours, with the engine sealed up and left alone.

Part 1 Ends With A Waiting Game

This video is labeled Part 1, and it closes the way a good project video should, on a cliffhanger. The oil is soaking, the covers are on and the builder asks viewers to save the video so they do not miss what happens next.

For anyone who has a stuck engine of their own, the story is a reminder that a seized motor does not automatically mean a scrapped one. Surface rust in the cylinders and valve train can sometimes be coaxed loose with patience, penetrating oil and the right order of steps.

More Stories You May Like

Leave a Reply

Your email address will not be published. Required fields are marked *